CeskyFrenchGermanItalianPortugueseTurkceSpanish

How to calculate profit
04/18/2016
How to recognize alcohol
04/18/2016

How to set up Satellite Internet

How to customize the Satellite Internet

In today's world, satellite Internet is not just a popular solution, but a real necessity for many users.

We'll tell you how to own and completely free to set up satellite Internet.

Since the satellite Eutelsat W6 (21.5) is the most common among satellite internet users, then we will look at setting it on his example.

You will need

  • - Dish,
  • - Converter,
  • - Cable,
  • - Bracket,
  • - DVB card
  • - Anchor
  • - F-ki,
  • - shrinking

instructions

1

To begin setting up satellite internet,make sure that all the necessary equipment you have available: a plate (90cm diagonal 1.20m?), converter, cable, bracket, DVB card, anchor, F-ki, shrinking.

2

Before you start setting directlysatellite internet, you need to establish a terrestrial channel (GPRS, DialUp or others.). How do you tell your provider or a mobile operator.

3

Next stage ? Stage setting DVB-card. Install DVB-card into an available PCI slot, preferably as far as possible from the TV-tuner, to avoid interference. Next take the drive going with DVB-card and install the drivers from this disk. DVB-map should be defined as a network device. Once you have installed the driver, a red icon will appear in the tray bar. Now right-click the icon and in the opened tab, select Setup4PC line.

4

In the window that appears, select? Add ?, enter the satellite name? Eutelsat W6 ?, leave everything else unchanged. Click? OK ?.

5

Click? Transponder Management? and in the window that appears, click? Add ?. Make a new transponder (11345, 28782 speed, polarization? H? (Horizontal). Further, if the satellite is configured correctly, you will see the band of the signal level (Signal Quality). Click? OK ?,? Close ?.

6

Next in the window? Setup4PC? select the button? Data Services ?. In the resulting window, select the name of the provider (provider name) and click? Add ?. Enter name? SpaceGate ?.

7

Now in the window? Transponder? click? Add? and in the window that opens, select the transponder which you sacrificed frequency. Enter another name for display in the tray panel. Click OK.

Enter? PID List ?,? 1024? and press? Insert ?. Then,? OK? and? Close ?.

8

Now configure the network connection. Go to the menu? Start? //? Setup? // ?Network connections?. Right click on the? Network Connections? and go to the? Properties ?. In the tab? General? select the protocol? TCP / IP? and click on? Properties ?. Drive the IP-address, which is on the list of personal settings, going along with DVB-card. And your subnet mask must be 255.255.255.0. Click? OK ?.

9

Download software from the Internet? GlobaX ?. Go to the directory where you installed GlobaX and find the file? globax.conf ?. Open it in a normal notebook, and enter the following data:

[Server]

port = 2001

log = client.log

[Remote]

name = globax

server = (each individual subscriber, goes along with DVB-card)

login = (each individual subscriber, goes along with DVB-card)

passwd = (each individual subscriber, goes along with DVB-card)

speed_in = 100000

speed_out = 4096

mtu = 1500

mru = 1500

[Local]

remote = globax

port = 127.0.0.1:3128

service_int = 0

[Local]

remote = globax

port = 127.0.0.1:1080

service_int = 2
Save and close the document.

10

Configure your browser if it is not accepted the settings automatically.

Open your browser, click the? Service? //?Internet Options, select the tab ?,? Connections? and locate the ground connection (DialUp, GPRS). Select it and click the? Setup ?. Enter the address 127.0.0.1 and port 3178. Click? OK ?.

11

Connect to the Internet. Once a computer connects, note the driver icon on the tray bar, it should be green. If so, connect the ground line. Then go to the directory, run the program? GlobaX ?, click? Start ?. Done! Open your browser and use satellite Internet with pleasure!

Comments are closed.