CeskyFrenchGermanItalianPortugueseTurkceSpanish

How to install the OSes
04/27/2016
How to remove the user from the blacklist
04/27/2016

How to close the middle loop

How to close the middle loop

The need to close the loop, located in the middle of the series, most likely to occur when knitting the neck.

Even with a zipper on the shelf or the back of the second part fit one canvas.

The seam in the middle does not decorate the product, unless it is provided is shaped and not decorative.

At the same time the majority of products the neck should be symmetrical.

That is strictly necessary to close a certain number of loops.

You will need

  • - Product related to the desired vysotu-
  • - Spokes (preferably on the line) -
  • - The second ball of the same pryazhi-
  • - Sample vyazki-
  • - Pattern or merki-
  • - Line or centimeter.

instructions

1

Count how many loops you need to close. At the beginning of the work you have already calculated their number to dial. In this case, the principle is the same. Measure the width of the pattern on the cut. To measure is necessary between the outermost points of the horizontal line of the neck, where the ascent begins on the shoulders. Multiply the resulting amount by the number of loops in one centimeter. For example, the density of knitting have 3 loops of 1 cm, and the distance between the lifting points on the shoulder is 15 cm. Multiplying 15 by 3, you get 45. So many loops should be closed.

2

Since the dates of your loops are in the middleseries, it is necessary to calculate how much you need to knit before closing. From the total number of loops are the spokes subtract those that will be closed. For example, the knitting width you have 80 loops. Subtract from this number 45 received 35 loops. This number must be divided by 2. In this case, it is odd, therefore, unnecessary to take the neck loop. That is not necessary to close the 45 and 46 loops. Knit to the neck must be 17 loops, counting an edge. If thick thread and needles, and crochet loose, you can do another thing. Excess loop added to one shoulder. In this case, the knit loops require 18, 44 and then close to retain the second arm 18.

3

Start the last row. This can be done in two ways, depending on whether you knit shoulders simultaneously or sequentially. In the first case, start with the same number of spokes. Knit better on both circular, but it is possible to direct. In the second case, use the extra spokes. Knit her first row shoulder and leave the loop on it. In any case, there should be as much as you have defined on the shoulder. Close average loop in the second case, you will be the same needles, which knit the entire article.

4

Close average Loop start with a loop located behind the lastshoulder loop. Knit it together with the next to the right and remove the needle as you would normally. Follow the illustration. If the second loop paired Wrong, wrong provyazyvayte edge loop, if the face - the face. Close the desired number of loops. Compare the width of the shoulders.

5

Dovyazhite row and turn the work. If you are going to carry the side portions at a time, do it first, which has just passed. Tie it to the end, tear off the thread and tighten. Go to the second shoulder. Since you have completed a series of loops before the middle, then you need to start following by closing the line.

6

Shoulders can be knit at the same time. It's even more convenient, since this method makes it easier to observe the symmetry. Close the right amount of middle-loops and finish line. Turn the work, knit the first row of shoulder and push it to the end of the spokes, which is limiting, or else on the line. Tie the thread from the second coil to the top line of the closure and tie the first row of the other side wall. The next series start from the same coil. Dovyazhite it to the neck, slide the hinges to the limiter. Pass closed average loops and finish a number of thread from the first coil. Thus knit to the end part.

Comments are closed.